搜索
搜索
01

01

02

02

03

03

Common Faults and exclusion method of drilling rig

  • 分类:Technology2
  • 作者:
  • 来源:
  • 发布时间:2010-02-06
  • 访问量:0

【概要描述】Common Faults and exclusion method of drilling rig Motor does not turn Reason:Power unreasonable, or joint loosening Remedy:

Common Faults and exclusion method of drilling rig

【概要描述】Common Faults and exclusion method of drilling rig Motor does not turn Reason:Power unreasonable, or joint loosening Remedy:

  • 分类:Technology2
  • 作者:
  • 来源:
  • 发布时间:2010-02-06
  • 访问量:0
详情
Common Faults and exclusion method of drilling rig
Motor does not turn
Reason:Power unreasonable, or joint loosening
Remedy:
 
Reason :restore power, check all connectors and tighten
Remedy:
 
Reason:Action is not reset after the overcurrent protection device
Remedy:Press the reset button to restart the motor
 
Reason:Over-current protection device is damaged
Remedy:Replacement of over-current protection device
 
Slow drilling
Reason:Drill the end of life
Remedy:Replaced with new drill bits
 
Reason:Drill feed pressure is too low
Remedy:Increase the feed pressure
 
Reason:Drill Segment surface is fine crumb paste to live
Remedy:Cleaning drill, increase water pressure
 
Reason: skid result in Cut into thick steel
Remedy:Feed pressure decreases, and then increase the pressure to be reinforced through
 
Reason:Processing chip plot in thehole
Remedy:Clean-up the hole-bottom and inflating
 
Reason:Flow not smooth,Leakage or non-return
Remedy:Check water inlet valve, check the flow
 
Reason:Sharpness bit lower
Remedy:Use bricks or grinding wheel to re-open edge
Bit stuck:
 
Reason:Block of reinforcement metal or debris stuck in the drill core and drill bit and hole wall or between the between the.
Remedy:Stop the machine, using wrench turning left and right bit, or pull out the drill bit crack coring
 
Reason:Rack is not strong, resulting in displacement of
Remedy:Re-fixed the Rack
 
Reason:Rack column and sleeve gap is too large
Remedy:Adjust the sleeve gap
 
Drill wall wear too fast
Reason:Drill spindle is not core 
Remedy:Repair or replacement of spindle
 
Reason:the bit errors
Remedy:Replacement the Bits
 
Reason:reinforcement metal or thin debris can not be discharged outside the hole
Remedy:To improve the water flow, remove the drill bit, clean the hole
 
Water jacket leaking
Reason:Skeleton ring wear or aging
Remedy:Replacement the rubber seal ring

扫二维码用手机看

关联新闻

我司2019亚洲(泰国)混凝土展圆满结束

我司2019亚洲(泰国)混凝土展圆满结束

2019年9月7日,亚洲(泰国)混凝土展在泰国曼谷黑圆满结束!   我司带去很多自己设计与研发的特殊齿形的锯片、磨轮、钻头等产品,在为期3天的展会中吸引了很多客户前去参观和咨询。
2019-09-11
我司慕尼黑宝马展圆满结束

我司慕尼黑宝马展圆满结束

德国宝马展在慕尼黑圆满结束!   我司带去很多自己设计与研发的特殊齿形的锯片、磨轮等产品,吸引了很多客户前去参观和咨询。
2019-04-22
万邦工具诚邀您参加125届广交会,展位号:14.3I05

万邦工具诚邀您参加125届广交会,展位号:14.3I05

武汉万邦激光金刚石工具股份有限公司 我司将参加广交会,展位号:14.3I05.参展时间:2019.4.15-4.19.
2019-03-22
我司将参加德国宝马展2019.4.8-4.14,展位号:A1-514A

我司将参加德国宝马展2019.4.8-4.14,展位号:A1-514A

武汉万邦激光金刚石工具股份有限公司 我司将参加德国宝马展,展位号:A1-514A.参展时间:2019.4.8-4.14.参展地址:慕尼黑展览中心
2019-03-22

武汉万邦激光金刚石工具股份有限公司

地址: 武汉经济技术开发区车城大道280-8号
电话:+86-27-84222369/84473270

手机:13971678882
传真: +86-27-84222515
邮箱:kristyxuke@wanbanglaser.com

留言应用名称:
客户留言
description
验证码

版权所有:武汉万邦激光金刚石工具股份有限公司     鄂ICP备07507631号    网站建设:中企动力 武汉